output specifications rr2-s04/d04 4 watt regulated single & dual output absolute maximum ratings (4) 1) typical value at nominal input voltage and full load. 2) tested by nominal vin and constant resistive load. 3) measured input reflected ripple current with a simulated source inductance of 12uh. 4) exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. 5) operation under no-load conditions will not damage these devices. however they may not meet all listed specifications. 6) its necessary to add a minimum capacitor in output for some models. please check single model datasheet for detail value. the models listed are just for standard type. if you need a special specification product, please contact our service. phone: +49 69 984047-0, mail to: info@rsg-electronic.de or use the forms on www.rsg-electronic.de (?kontakt). dip24, w ide 2:1 input range full smd technology 1500 vdc isolation up to 3500 vdc isolation continuous short circuit protection efficiency up to 82% -25c~85c operation temperature range optional metal case voltage accuracy 1% line regulation 0.5% load regulation 0.5% ripple & noise (20 mhz bandwith) (1) 60 mv pk-pk short circuit protection continuous temperature coefficient 0.02%/c capacitor load (2) see table voltage range see table max. input current see table no-load input current see table input filter pi type input reflected ripple current (3) 35 ma pk-pk input specifications efficiency see table i/o isolation voltage (3 sec.) input / output 1500 ~ 3500 vdc metal case / input & output 1000 vdc i/o isolation capacitance 60 pf typ. i/o isolation resistance 1000 m ohm switching frequency 100~400 khz humidity 95% rel. h reliability calculated mtbf (mil-hdbk-217f) > 2.199 mhrs. safety standard (designed to meet) iec 60950-1:2001 general specifications case material non-conductive black plastic (ul94v-0 rated) nickel-coated copper base material non-conductive black plastic (ul94v-0 rated) pin material ? 0.5 mm brass solder-coated potting material epoxy (ul94v-0 rated) weight plastic 12.5 g, metal 15 g dimensions 1.25 x 0.8 x 0.4 physical specifications operating temperature (see derating curve) -25c~ 85c maximum case temperature 100c storage temperature -40c~125c cooling nature convection environment specifications note these are stress ratings. exposure of devices to any of these conditions may adversely affect long-term reliability. input voltage (100 ms) 12 modes -0.7 ~ 24 vdc 24 modes -0.7 ~ 40 vdc 48 modes -0.7 ~ 80 vdc lead soldering temperature 260c (1.5 mm from case 10 sec.) all specifications typical at ta = 25c, nominal input voltage and full load unless otherwise specified. the information and specifications contained in this data sheet are believed to be correct at time of publication. however, we accept no responsibility for consequences arising from printing errors or inaccuracies. subject to change without notice. page: 1/3 last update: 06.02.09
rr2-s04/d04 4 watt regulated single & dual output derating curve model number input input current (ma) output output current output current efficiency capacitor range no load/full load vdc min. load (ma) full load (ma) @fl (%) load ( hf) vdc rr2-1205s04ax 9-18 20 / 432 5 200 800 77 2200 rr2-1209s04ax 9-18 20 / 416 9 111 444 80 470 rr2-1212s04ax 9-18 20 / 416 12 83.3 333 80 470 rr2-1215s04ax 9-18 20 / 416 15 66.8 267 80 470 rr2-1224s04ax 9-18 20 / 416 24 41.8 167 80 220 RR2-1205D04AX 9-18 20 / 432 5 100 400 77 1000 rr2-1209d04ax 9-18 20 / 416 9 55.5 222 80 220 rr2-1212d04ax 9-18 20 / 416 12 41.8 167 80 220 rr2-1215d04ax 9-18 20 / 416 15 33.3 133 80 220 rr2-1224d04ax 9-18 20 / 416 24 20.8 83 80 100 rr2-2405s04ax 18-36 12 / 210 5 200 800 79 2200 rr2-2409s04ax 18-36 12 / 203 9 111 444 82 470 rr2-2412s04ax 18-36 12 / 203 12 83.3 333 82 470 rr2-2415s04ax 18-36 12 / 203 15 66.8 267 82 470 rr2-2424s04ax 18-36 12 / 203 24 41.8 167 82 220 rr2-2405d04ax 18-36 12 / 210 5 100 400 79 1000 rr2-2409d04ax 18-36 12 / 203 9 55.5 222 82 220 rr2-2412d04ax 18-36 12 / 203 12 41.8 167 82 220 rr2-2415d04ax 18-36 12 / 203 15 33.3 133 82 220 rr2-2424d04ax 18-36 12 / 203 24 20.8 83 82 100 rr2-4805s04ax 36-72 8 / 106 5 200 800 78 2200 rr2-4809s04ax 36-72 8 / 101 9 111 444 82 470 rr2-4812s04ax 36-72 8 / 101 12 83.3 333 82 470 rr2-4815s04ax 36-72 8 / 101 15 66.8 267 82 470 rr2-4824s04ax 36-72 8 / 101 24 41.8 167 82 220 rr2-4805d04ax 36-72 8 / 109 5 100 400 76 1000 rr2-4809d04ax 36-72 8 / 101 9 55.5 222 82 220 rr2-4812d04ax 36-72 8 / 101 12 41.8 167 82 220 rr2-4815d04ax 36-72 8 / 101 15 33.3 133 82 220 rr2-4824d04ax 36-72 8 / 101 24 20.8 83 82 100 model selection guide page: 2/3 last update: 06.02.09 number structure isolation 1 =1.5 kvdc 3=3.5 kvdc power 04=4w output 05=5v 09=9v 12=12v 15=15v 24=24v code internal rr2 - xx xx s 04 a 1 (m) type s =single d=dual input 12=9~18v 24=18~36v 48=36~72v name/package rr2=dil24 add suffix ?m for metal case! if no suffix mean plastic case.
mechanical specifications for high isolation models rr2-s04/d04 4 watt regulated single & dual output page: 3/3 last update: 06.02.09 mail: info@rsg-electronic.de www.rsg-electronic.de rsg electronic components gmbh sprendlinger landstr. 115 d-63069 offenbach tel. +49 69 984047-0 fax +49 69 984047-77 rsg rr2-xxxxx04ax mechanical specifications metal case rsg rr2-xxxxx04axm 24 pin dil package nickel coated copper ?m case 24 pin dil package non-conductive plastic all dimensions are typical in millimeters (inches). 1) pin diameter: 0.5 0.05 (0.02 0.002) 2) pin pitch tolerance: 0.35 ( 0.014) 3) case tolerance: 0.5 ( 0.02) all dimensions are typical in millimeters (inches). 1) pin diameter: 0.5 0.05 (0.02 0.002) 2) pin pitch tolerance: 0.35 ( 0.014) 3) case tolerance: 0.5 ( 0.02)
|
